济南震辉保温材料有限公司

0531-87266820
当前位置:首页>新闻资讯-行业动态-挤塑板在粘贴时应注意什么
分类导航
联系我们
二维码 震辉保温材料

服务热线:0531-87266820

联系电话:13791062737

联系地址:章丘工业园

挤塑板在粘贴时应注意什么

文章来源:https://www.sdjnxps.com/作者:震辉保温材料 发布时间: 2021-07-30
说到挤塑板,大家清楚挤塑板在粘贴的时候有哪些是需要注意的吗?感兴趣的朋友可以了解一下,那么下面济南挤塑板厂家来对它做一个详细的介绍吧!
Speaking of Extruded Boards, do you know what needs attention when pasting extruded boards? Interested friends can learn about it, then the following Jinan extruded plate manufacturer to make a detailed introduction to it!
要保证挤塑板、网络布的规格和各项技术指标,挤塑板聚合物砂浆配置原料质量一定要符合要求;然后挤塑板须和墙面粘贴牢固,不能出现松动和徐粘现象;然后聚合物砂浆和挤塑板须要粘贴紧密,不能出现脱层、空鼓、裂缝和爆灰现象。
To ensure the specifications and technical indicators of extruded plate and network cloth, the quality of raw materials for polymer mortar of extruded plate must meet the requirements; Then, the extruded plate must be firmly adhered to the wall, and there shall be no looseness and creep; Then, the polymer mortar and the extruded board shall be pasted tightly without delamination, hollowing, crack and ash explosion.
用一只干净的塑料搅拌桶倒入无份干混砂浆,按5:1的比例加水,边加水边搅拌,之后再用搅拌器搅拌5分钟左右,挤塑板稠度均匀适中即可,另外保证砂浆有一定粘度。
Use a clean plastic mixing bucket to pour the dry mixed mortar, add water at the ratio of 5:1, mix while adding water, and then use a mixer to mix for about 5 minutes. The consistency of the extruded plate can be uniform and moderate, and ensure that the mortar has a certain viscosity.
挤塑板和基层面的总粘贴,面积为30%-50%,固定件的胀塞部分进入结构墙体要大于50;然后挤塑板的碰头缝不能末粘接剂;再然后网络布要横向铺贴,压粘要密实,不能有空鼓、翘边等现象,水平方向搭接宽度大于100,垂直方向大于80;再就是聚合物砂浆厚度要小于4,首层小于5。
The total bonding area between the extruded plate and the base layer is 30% - 50%, and the expansion part of the fixed part into the structural wall is more than 50%; Then the joint of the extruded plate shall not be free of adhesive; Then, the network cloth shall be laid horizontally, and the pressure bonding shall be dense. There shall be no hollowing, edge warping and other phenomena. The lap width in the horizontal direction shall be greater than 100, and that in the vertical direction shall be greater than 80; The thickness of polymer mortar shall be less than 4, and the first layer shall be less than 5.
济南挤塑板厂家
挤塑板板粘牢后,随时用专用的搓抹子将板边的不平之处搓平,尽量减少板与板之间的高差接缝,当板缝间隙大于2㎜时,应用挤塑板条填实后磨平。
After the extruded plate is firmly adhered, the uneven part of the plate edge shall be rubbed with a special trowel at any time to minimize the height difference joint between the plates. When the gap between the plates is more than 2mm, the extruded plate shall be filled and polished.
在墙角处,挤塑板应垂直交错连接,保证拐角处板材安装的垂直度。
At the corner of the wall, the extruded plates shall be vertically staggered to ensure the perpendicularity of the plate installation at the corner.
挤塑板表面不平整处应用专用打磨抹子磨平,然后将整个墙面打磨一遍。打磨时散落的聚苯屑应随时用刷子、扫把清理干净。
The uneven part of the extruded plate surface shall be smoothed with a special polishing trowel, and then the whole wall shall be polished once. The polystyrene chips scattered during grinding shall be cleaned up with a brush and broom at any time.
粘贴挤塑板时应注意以下事项:
The following matters shall be noted when pasting extruded plate:
操作应迅速,在挤塑板安装就位之前,粘接胶浆不得有结皮;
The operation shall be rapid. Before the extrusion plate is installed in place, the adhesive paste shall not have crust;
挤塑板的接缝应紧密,且平齐;不得在挤塑板侧面涂抹粘接胶浆,或挤入粘接胶浆;
The joints of extruded plates shall be tight and flush; Do not apply adhesive paste on the side of the extruded plate or squeeze adhesive paste into it;
门窗洞口角部的挤塑板,应采用整块挤塑板裁出洞口,不得拼接;
For the extruded plate at the corner of the door and window opening, the whole extruded plate shall be used to cut the opening without splicing;
打磨墙面的动作应是轻柔的圆周运动,不得沿着与挤塑板接缝平行的方向打磨;
The action of polishing the wall surface shall be gentle circular motion, and shall not be polished along the direction parallel to the joint of the extruded plate;
挤塑板粘贴施工完毕后,至少需间隔24小时,才能进行打磨,以防止挤塑板移动,减弱板材与基层墙体的粘接。
After the adhesive construction of the extruded plate is completed, the polishing can be carried out at least 24 hours apart to prevent the movement of the extruded plate and weaken the adhesion between the plate and the base wall.
挤塑板在粘贴时应注意什么?以上就是相关的注意事项了,您在操作之前建议是多去了解正确的使用方式以及相关问题,您也可以来我们网站https://www.sdjnxps.com咨询。
What should be paid attention to when pasting extruded boards? The above are the relevant precautions. Before operation, you are advised to learn more about the correct usage and related problems. You can also visit our website https://www.sdjnxps.com consulting service